L PROPELLER SHAFTS AND UNIVERSAL JOINT S move the snap rings pinch the ends together with After the removal of the one set of bearing races a pair of pliers If the rings do not readily snap release the other set by removing the snap rings out of the groove tap the end of the bearing lightly in the sleeve yoke by pinching the ends together which will relieve pressure against the rings with a pair of pliers Should the rings fail to snap After removing the snap rings press on the end of readily from the groove tap the end of the bearing one bearing until the opposite bearing is pushed lightly which will relieve the pressure against them from the yoke arm Turn the joint over and press Press on the end of one bearing until the opposite the first bearing back out of that arm by pressing bearing is pushed out of the yoke arm Turn the on the exposed end of the journal shaft Use a soft universal joint over and press the first bearing out ground drift with a Hat face about s 0 8 mm by pressing on the exposed end of the journal as smaller in diameter than the hole in the yoke arm sembly Use a soft ground drift with a Hat face and drive it out otherwise there is danger of damag about g 0 8 mm smaller in diameter than the ing the bearing hole in the yoke arm and drive out the bearing Lift Repeat this operation for the other two bearings the journal out by sliding to one side Clean all then lift out journal assembly by sliding it to one parts and check for wear side L 6 U Bolt Type Assembly L 4 Snap Rm g Typ ASSembly Wash all parts in cleaning solvent and inspect the Wash all parts ln eleaamg s lve e a d mspeet the parts after cleaning Replace any parts that indicate Parts alter eleaamg Replaee any Parts that mdloare extensive wear It is advisable to install new gaskets extensive wear It is advisable to install new gaskets on the journal assembly regardless of the condltlon ea the Jeumal assembly regardless ef the e ll er the old gaskets Make certain that the grease of the old gaskets Make certain that the grease Channel in each journal trnnrnon is ooen Channel m eael Journal rrunnlon ls open Pack the bearing cones one third full of lubricant Pack the bearing cones one third full of lubricant and install the rollers and lnstall the rollers Draw the bearings into the end yoke arm and seat Draw the bearmgs me the engl yoke arm and seat them firmly against the bearing shoulders Hold the them flrgnly agalnsr rlle bearlng shoulders Held bearings in a vertical position to prevent the the bearings in a vertical position to prevent the needles rorn dropping out until the joint is as needles from droplomg est until the Jemt ls as sembled If the joint binds when assembled tap sem oled ll the Jolnr l ls When assembled rap the arms lightly to relieve any pressure on the 1 the arms lightly to relieve any pressure on the bear bearings at the end of the jour nal Tighten the lngs at the end ef the Journal U bolts equally U bolt torque wrench reading is 15 to 20 lb ft 2 07 a 2 76 kg m 5 U Belt Type Dwassembly When installing the assembly in the vehicle be snte Removal of the attaching U bolt releases one set that the arrows on the propeller shaft and yoke of bearing races Slide the propeller shaft into the sleeve are in alignment as shown in Fig L 2 or yoke flange to remove them using care not to lose that the unmarked joints are aligned with the the rollers yokes in the same parallel plane SPECIFICATIONS L Z PROPELLER SHEETS HND UNIVERSHL IOINTS Make SPICER Dimensions rr Front if 7 P4 W 7 477 rm nn m Q erarrn 7 7777 rr 7 77 l O D Length KK 7 7 in rW D drWKr in rrrierirgth 7 if K F4 Engine Vehicles W H 777 I PE MUYVWVR Cj 5 C 5A 3 Speed l 1 3 175 cm 22 57 78 cm 1 4 45 cm 18 2 45 95 cm 4 Speed 1 3 175 cm 28 lg 72 39 cm 1 4 45 cm l 13 34 131 cm C 6 C 6A 3 Speed 1 3 175 cm 22 57 78 cm 1 4 45 cm 38 97 79 cm 4 Speed 1 3 175 cm 28l Q 72 39 cm 1 4 45cm 33l 84 69 cm C 3B 1 3 175 em V 33l4 85 57 cm 1 4 45 em 19 6 50 64 em D 5 l 1 4 45 em 24 gi 61 60 em D 6 l 3 7 62 cm 44lj 112 40 cm l V 6 Engine Vehicles l Q l C 5 C SA 3 Speed 1 3 175 cm 21 55 25 cm 2 5 08 cm 195 50 64 cm C 6 Cj 6A 3 Speed 1l4 3 175 cm 2l 55 25 cm 2 5 08 cm 39 99 06 cm Cj 5 4 Speed 1l 3 175 em 1 26l3 68 10 cm l 1 4 45 em 14 37 47 cm UNIVERSAL JOINTS l Make l Spicer Type Cardan Cross Bearing Antifriction 276